1. On 08/04/2022, Commerce published in the Federal Register its affirmative preliminary determination of sales at less than fair value and postponement of the final determination in the antidumping duty investigation of certain steel nails from Thailand (87 FR 47708). 2. The merchandise covered by this investigation is certain steel nails having a nominal shaft or shank length not exceeding 12 inches. Certain steel nails include, but are not limited to, nails made from round wire and nails that are cut from flat-rolled steel or long-rolled flat steel bars. Certain steel nails may be of one piece construction or constructed of two or more pieces. Examples of nails constructed of two or more pieces include, but are not limited to, anchors comprised of an anchor body made of zinc or nylon and a steel pin or a steel nail; crimp drive anchors; split-drive anchors, and strike pin anchors. Also included in the scope are anchors of one piece construction. Certain steel nails may be produced from any type of steel, and may have any type of surface finish, head type, shank, point type and shaft diameter. Finishes include, but are not limited to, coating in vinyl, zinc (galvanized, including but not limited to electroplating or hot dipping one or more times), phosphate, cement, and paint. Certain steel nails may have one or more surface finishes. Head styles include, but are not limited to, flat, projection, cupped, oval, brad, headless, double, countersunk, and sinker. Shank or shaft styles include, but are not limited to, smooth, barbed, screw threaded, ring shank and fluted. Screw-threaded nails subject to this proceeding are driven using direct force and not by turning the nail using a tool that engages with the head. Point styles include, but are not limited to, diamond, needle, chisel and blunt or no point. Certain steel nails may be sold in bulk, or they may be collated in any manner using any material. Excluded from the scope are certain steel nails packaged in combination with one or more non-subject articles, if the total number of nails of all types, in aggregate regardless of size, is less than 25. If packaged in combination with one or more non-subject articles, certain steel nails remain subject merchandise if the total number of nails of all types, in aggregate regardless of size, is equal to or greater than 25, unless otherwise excluded based on the other exclusions below. Also excluded from the scope are certain steel nails with a nominal shaft or shank length of one inch or less that are a component of an unassembled article, where the total number of nails is sixty (60) or less, and the imported unassembled article falls into one of the following eight groupings: (1) Builders' joinery and carpentry of wood that are classifiable as windows, French-windows and their frames; (2) builders' joinery and carpentry of wood that are classifiable as doors and their frames and thresholds; (3) swivel seats with variable height adjustment; (4) seats that are convertible into beds (with the exception of those classifiable as garden seats or camping equipment); (5) seats of cane, osier, bamboo or similar materials; (6) other seats with wooden frames (with the exception of seats of a kind used for aircraft or motor vehicles); (7) furniture (other than seats) of wood (with the exception of (i) medical, surgical, dental or veterinary furniture; and (ii) barbers' chairs and similar chairs, having rotating as well as both reclining and elevating movements); or (8) furniture (other than seats) of materials other than wood, metal, or plastics (e.g., furniture of cane, osier, bamboo or similar materials). The aforementioned imported unassembled articles are currently classified under the following Harmonized Tariff Schedule of the United States (HTSUS) subheadings: 4418.10, 4418.20, 9401.30, 9401.40, 9401.51, 9401.59, 9401.61, 9401.69, 9403.30, 9403.40, 9403.50, 9403.60, 9403.81 or 9403.89. Also excluded from the scope of this investigation are nails suitable for use in powder-actuated hand tools, whether or not threaded, which are currently classified under HTSUS subheadings 7317.00.2000 and 7317.00.3000. Also excluded from the scope of this investigation are nails suitable for use in gas-actuated hand tools. These nails have a case hardness greater than or equal to 50 on the Rockwell Hardness C scale (HRC), a carbon content greater than or equal to 0.5 percent, a round head, a secondary reduced-diameter raised head section, a centered shank, and a smooth symmetrical point. Also excluded from the scope of this investigation are corrugated nails. A corrugated nail is made up of a small strip of corrugated steel with sharp points on one side. Also excluded from the scope of this investigation are thumb tacks, which are currently classified under HTSUS subheading 7317.00.1000. Also excluded from the scope are decorative or upholstery tacks. Certain steel nails subject to this investigation are currently classified under HTSUS subheadings 7317.00.5501, 7317.00.5502, 7317.00.5503, 7317.00.5505, 7317.00.5507, 7317.00.5508, 7317.00.5511, 7317.00.5518, 7317.00.5519, 7317.00.5520, 7317.00.5530, 7317.00.5540, 7317.00.5550, 7317.00.5560, 7317.00.5570, 7317.00.5580, 7317.00.5590, 7317.00.6530, 7317.00.6560, and 7317.00.7500. Certain steel nails subject to this investigation also may be classified under HTSUS subheadings 7318.15.5090, 7907.00.6000, 8206.00.0000, or other HTSUS subheadings. While the HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of this investigation is dispositive. 3. This proceeding has been assigned case number A-549-844. 4. For imports of certain steel nails from Thailand, CBP shall suspend liquidation of such shipments entered, or withdrawn from warehouse, for consumption on or after 08/04/2022. Effective 08/04/2022, CBP shall require, for such entries, a cash deposit equal to the margins for the producers and/or exporters listed below: Producer and/or Exporter: Come Best (Thailand) Co. Ltd Case number: A-549-844-001 Cash deposit rate: 17.12% Producer and/or Exporter: Jinhai Hardware Co., Ltd Case number: A-549-844-002 Cash deposit rate: 65.87% All Others Case Number: A-549-844-000 Cash Deposit Rate: 17.12% 5. If any entries of this merchandise are exported by a firm other than the producer, then the following instructions apply: A. If the exporter of the subject merchandise does not have its own rate but the producer has its own rate, the cash deposit rate will be the producer's rate. B. Where neither the exporter nor the producer has its own rate or the producer is unknown, use the all-others rate of 17.12 percent to establish the cash deposit. 6. If there are any questions by the importing public regarding this message, please contact the Call Center for the Office of AD/CVD Operations, Enforcement and Compliance, International Trade Administration, U.S. Department of Commerce at (202) 482-0984. CBP ports should submit their inquiries through authorized CBP channels only. (This message was generated by OIII: MP.) 7. There are no restrictions on the release of this information. Alexander Amdur